Efeito dos diferentes tipos de polimento sobre a rugosidade de superfície de uma resina acrílica comercial quimicamente ativada: estudo in vitro / Effect of different types of polishing on the surface roughness of a chemically activated commercial acrylic resin: an in vitro study

Objetivo: avaliar in vitro o polimento sobre resina acrílica quimicamente ativada (RAQA), por meio da rugosidade de superfície (Ra). Materiais e Método: Foram confeccionadas 40 amostras de RAQA, com dimensões de 10 a 10 x 2 mm, e foram divididas em quatro grupos (n=10): ausência do acabamento (AA); Ausência de polimento (AP); Polimento químico (PQ); Polimento com borrachas siliconadas + Escovas (PM). Os espécimes foram avaliados no quanto a rugosidade média (Ra) antes e após o envelhecimento em água destilada em uma estufa por 60 dias. Três medições de Ra (µm), na horizontal foram realizadas e calculada uma média para cada espécime. Os dados foram analisados de forma descritiva e inferencial, ANOVA de medidas repetidas e teste de Tukey com nível de significância de 5%. Resultados: Inicialmente, o grupo AA teve os menores valores de Ra e o grupo AP os maiores valores de rugosidade, com média e desvio padrão respectivamente 0,17 (±0,11) e 0,52 (±0,10). Após o envelhecimento, o grupo AA teve as menores médias e o grupo PQ os maiores valores de Ra, sendo 0,38 (±0,20) e 1,33 (±0,32), respectivamente. Os resultados evidenciaram diferença estatística significante quando as amostras foram submetidas ao acabamento com brocas. Conclusão: A RAQA necessita de polimento após acabamento com brocas, uma vez que a ausência de polimento comprometerá a lisura de superfície do material.(AU)

Objective: to evaluate in vitro polishing on chemically activated acrylic resin (RAQA), using surface roughness (Ra). Materials and Method: 40 RAQA samples were made, measuring 10 to 10 x 2 mm, and divided into four groups (n=10): absence of finishing (AA); Lack of polishing (AP); Chemical polishing (PQ); Polishing with silicone rubbers + Brushes (PM). The specimens were evaluated for their average roughness (Ra) before and after aging in distilled water in an oven for 60 days. Three horizontal Ra (µm) measurements were taken and an average was calculated for each specimen. Data were analyzed descriptively and inferentially, using repeated measures ANOVA and Tukey test with a significance level of 5%. Results: Initially, the AA group had the lowest Ra values and the AP group the highest roughness values, with mean and standard deviation respectively 0.17 (±0.11) and 0.52 (±0.10). After aging, the AA group had the lowest averages and the PQ group the highest Ra values, being 0.38 (±0.20) and 1.33 (±0.32), respectively. The results showed a statistically significant difference when the samples were finished with drills. Conclusion: RAQA requires polishing after finishing with drills, as the lack of polishing will compromise the surface smoothness of the material.(AU)

Effect of different mechanical surface treatments on flexural strength of repaired denture base / Efecto de diferentes tratamientos superficiales mecánicos sobre la resistencia a la flexión de la base de la dentadura reparada

Aim: To assess the effect of different mechanical surface treatments on flexural strength of repaired denture base. Material and Methods: Sixty bar-shaped specimens of heat-polymerized acrylic resin were fabricated, and divided into six groups (n=10). All specimens, except the positive control group (group PC), were sectioned into halves to create a 1-mm clearance. A negative control group with no surface treatment (group NC) was also considered. Other groups underwent different surface treatments: group Laser; treated with erbium: yttrium-aluminum-garnet (Er:YAG) laser, group APA; airborne-particle abrasion (APA), group APA plus Laser; a combination of laser and APA, and group Bur; bur grinding. After measuring surface roughness (Ra) with a profilometer, all sectioned specimens were repaired by auto-polymerizing acrylic resin, and thermocycled afterward. Three-point bending test was performed by a universal testing machine. Data were statistically analyzed (α=0.05). Results: The mean surface roughness of all experimental groups were significantly higher than that of group NC (p<0.05). The mean flexural strength of all groups was significantly lower than that of group PC (p<0.05). Group B had significantly higher flexural strength than the other surface-treated groups (p<0.05). Group Laser had significantly higher flexural strength than groups APA (p=0.043) and APA plus Laser (p=0.023). No significant difference was found between groups APA and APA plus Laser (p=0.684). Conclusion: All surface treatments increased the surface roughness and flexural strength compared with the untreated group. The highest flexural strength was observed in specimens treated by bur grinding and then laser, however, it was still significantly lower than intact specimens.

Objetivo: Evaluar el efecto de diferentes tratamientos superficiales mecánicos sobre la resistencia a la flexión de la base de la prótesis reparada. Material y Métodos: Se fabricaron sesenta especímenes en forma de barra de resina acrílica termo-polimerizada y se dividieron en seis grupos (n=10). Todas las muestras, excepto el grupo de control positivo (grupo PC), se seccionaron en mitades para crear un espacio libre de 1 mm. También se consideró un grupo de control negativo sin tratamiento superficial (grupo NC). Otros grupos se sometieron a diferentes tratamientos superficiales: grupo Láser; tratados con láser de erbio: itrio-aluminio-granate (Er:YAG), grupo APA; abrasión por partículas en el aire (APA), grupo APA más láser; una combinación de láser y APA, y grupo Bur; molienda de fresas. Después de medir la rugosidad de la superficie (Ra) con un perfilómetro, todas las muestras seccionadas se repararon con resina acrílica de autopolimerización y se sometieron a termociclado. La prueba de flexión de tres puntos se realizó con una máquina de prueba universal. Los datos se analizaron estadísticamente (α=0,05). Resultados: La rugosidad superficial media de todos los grupos experimentales fue significativamente mayor que la del grupo NC (p<0,05). La resistencia media a la flexión de todos los grupos fue significativamente menor que la del grupo PC (p<0,05). El grupo B tenía una resistencia a la flexión significativamente mayor que los otros grupos tratados en la superficie (p<0,05). El grupo Láser tuvo una resistencia a la flexión significativamente mayor que los grupos APA (p=0,043) y APA más Láser (p=0,023). No se encontró diferencia significativa entre los grupos APA y APA más Láser (p=0,684). Conclusión: Todos los tratamientos superficiales aumentan la rugosidad de la superficie y la resistencia a la flexión en comparación con el grupo sin tratar. La resistencia a la flexión más alta se observó en las muestras tratadas con fresado y luego con láser; sin embargo, aún era significativamente más baja que las muestras intactas.

In Vitro Effect of Acidic Challenges on the Physical Properties of Dental Prosthesis Artificial Teeth

Abstract Objective: To evaluate the effect of immersion and acid challenge with cola drink on color change (ΔE), Vickers hardness (VHN) and surface roughness (Ra) of artificial acrylic resin teeth. Material and Methods: The artificial teeth were divided into 6 groups (n= 8): TC (Trilux/Control), BC (Biotone/Control), TAC (Trilux/Acid challenge), BAC (Biotone/Acid challenge), TI (Trilux/Immersion) and BI (Biotone/Immersion). The teeth were embedded in acrylic resin and the labial side was serially polished to provide appropriate flat surface. The samples of TC, BC, TI, BI groups were immersed in artificial saliva and cola drink (coke) for 7 days, respectively. The acid challenge was performed with immersion of samples in coke for 5 min, and subsequently immersion in artificial saliva for 2h. This cycle was repeated at 4 times/day, during 7 days. The tests of VHN, ΔE and Ra were analyzed before and after the challenge and immersion groups. Data was analyzed by ANOVA, Tukey and T test (α = 0.05). Results: There was no difference in Ra values between groups after treatments. However, there was a decrease in VHN for all groups. BI (19.2 ± 0.3) presented significantly lower hardness than BAC (19.5 ± 0.9) and BC (20.2 ± 0.5). Groups BI (2.18 ± 0.41) and TI (1.50 ± 0.43) had statistically higher ΔE compared to the other groups. Conclusion: The hardness of resin teeth decreased after acid challenges, but the roughness surface was not affected. The color was more affected by the times of exposure in cola beverage and remineralization in artificial saliva, which were associated to the material degradation (AU).

Evaluation of the physical and antifungal effects of chlorhexidine diacetate incorporated into polymethyl methacrylate

Abstract This study aimed to evaluate the physical properties and antifungal activities of polymethyl methacrylate (PMMA) acrylic resins after the incorporation of chlorhexidine diacetate salt (CDA). Methodology: First, acrylic resin specimens were fabricated with Vipi Cor® and DuraLay® resins with and without the incorporation of 0.5%, 1.0% or 2.0% CDA. The residual monomer and CDA release were measured at intervals ranging from 2 hours to 28 days using ultraviolet spectrometry combined with high-performance liquid chromatography. The antifungal activity against C. albicans was evaluated with the agar diffusion method. Fourier transform infrared spectroscopy was used to analyze the degree of resin conversion. Finally, the water sorption values of the resins were also measured. Results: The incorporated CDA concentration significantly changed the rate of CDA release (p<0.0001); however, the brand of the material appeared to have no significant influence on drug release. Subsequently, the inhibition zones were compared between the tested groups and within the same brand, and only the comparisons between the CDA 2% and CDA 1% groups and between the CDA 1% and CDA 0.5% groups failed to yield significant differences. Regarding the degrees of conversion, the differences were not significant and were lower only in the CDA 2% groups. Water sorption was significantly increased at the 1.0% and 2.0% concentrations. Conclusions: We concluded that the incorporation of CDA into PMMA-based resins enabled the inhibition of C. albicans growth rate, did not alter the degrees of conversion of the tested resins and did not change the release of residual monomers.

Effect of the incorporation of zinc oxide nanoparticles on the flexural strength of auto- polymerized acrylic resins / Efecto de la incorporación de nanopartículas de óxido de zinc en la resistencia a la flexión de las resinas acrílicas autopolimerizadas

Background: Auto-polymerized acrylic resins are commonly used in many applications in dentistry including in maxillofacial rehabilitation such as interim prostheses, denture repair, reline, orthodontic appliances, record base, among others. These substances, however, have some negative aspects such as poor mechanical properties. Aim: The objective of the current study was to evaluate the effect of incorporating zinc oxide nanoparticles to auto-polymerized acrylic resins on their flexural strength. Materials and methods: Thirty specimens were made from auto-polymerized acrylic resins, divided into three main groups (1 control and 2 experimental). Each group had ten specimens. The two experimental groups comprised the zinc oxide powder at 1% and 2% concentrations, respectively. Acrylic specimens were fabricated with the dimension of 65mm length, 10mm width and 2.5mm thickness according to ISO 1567 specification 1999. Each specimen was subjected to the flexural strength test by a universal testing machine. The crosshead speed for the flexural strength test was 5mm/min until fracture occurred. The SPSS version 16 was utilized for the statistical analysis. The ANOVA and Tukey were used for the comparison among all groups. Results: there was a significant increase (p<0.001) in the flexural strength of the acrylic resins following the addition of zinc oxide particles (control group: 133.27 SD 1.73, ZnO 1%: 154.28 SD 2.90, ZnO 2%: 176.45 SD 0.94). Conclusions: The incorporation of zinc oxide nanoparticles has a significant effect on the flexural strength of auto-polymerized acrylic resins.

Antecedentes: Las resinas acrílicas autopolimerizadas se usan comúnmente en muchas aplicaciones en odontología, incluyendo la rehabilitación maxilofacial, en prótesis provisionales, reparación de prótesis, revestimientos, en aparatos de ortodoncia, bases de registro, entre otros. Estas sustancias, sin embargo, tienen algunos aspectos negativos tales como propiedades mecánicas deficientes. Objetivo: el objetivo del presente estudio fue evaluar el efecto de la incorporación de nanopartículas de óxido de zinc en la resistencia a la flexión de resinas acrílicas autopolimerizadas. Materiales y métodos: Treinta muestras de resinas acrílicas autopolimerizadas fueron hechas, divididas en tres grupos principales (un grupo control y dos experimentales), cada grupo con diez especímenes. Se incorporó polvo de óxido de zinc en los dos grupos experimentales, en concentraciones de 1% y 2%, respectivamente. Las muestras de acrílico se fabricaron con una dimensión de 65mm de longitud, 10mm de ancho y 2,5mm de espesor según la especificación ISO 1567 1999. Cada muestra se sometió a la prueba de resistencia a la flexión mediante una máquina de prueba universal. La velocidad de la cruceta para la prueba de resistencia a la flexión fue de 5mm/min hasta que se produjo la fractura. Se utilizó la versión SPSS 16 para el análisis estadístico. El ANOVA y Tukey se utilizaron para la comparación entre todos los grupos. Resultados: Se observó un aumento significativo (p<0.0 01) en la resistencia a la flexión de las resinas acrílicas luego de la adición de partículas de óxido de zinc (grupo de control: 133,27 SD 1,73 MPa, ZnO 1%: 154,28 SD 2,90 MPa, ZnO 2%: 176,45 SD 0,94 MPa). Conclusiones: La incorporación de nanopartículas de óxido de zinc tiene un efecto significativo en la resistencia a la flexión de las resinas acrílicas autopolimerizadas.

Surface morphologic evaluation of orthodontic bonding systems under conditions of cariogenic challenge

Abstract: Orthodontic bonding systems are submitted to demineralization and remineralization dynamics that might compromise their surface smoothness, and favor biofilm aggregation and caries development. The aim of the present study was to evaluate the effects of a cariogenic challenge model (in vitro pH-cycling model) on the surface roughness and topography of 3 bonding materials: Transbond™ XT (XT), Transbond™ Plus Color Change (PLUS) and Fuji Ortho™ LC (FUJI), by means of Atomic Force Microscopy (AFM). Six specimens with standardized dimensions and surface smoothness were fabricated per group, and the materials were manipulated in accordance with the manufacturers' instructions. No polishing was necessary. AFM tests were performed before and after pH-cycling, taking 3 readouts per specimen. The roughness results (Ra) were obtained at nanometric levels (nm) and surface records were acquired in two- and three-dimensional images of height and lock-in phase of the material components. The surfaces of all groups analyzed in the study were morphologically altered, presenting images suggestive of matrix degradation and loss of matrix-load integrity. FUJI presented the greatest increase in surface roughness, followed by XT and PLUS, respectively (p≤0.001). Nevertheless, the roughness values found did not present sufficient degradation to harbor bacteria. The surface roughness of all tested materials was increased by pH-cycling. The use of materials capable of resisting degradation in the oral environment is recommended, in order to conserve their integrity and of the surrounding tissues.

Color stability and surface roughness of chitosan- and nanodiamond-modified bisacrylic resin

Abstract: The aim of this study is to evaluate the effect of chitosan or nanodiamond incorporation on the color stability and surface roughness of a bisacrylic resin subjected to artificial aging. Four bisacrylic resins were evaluated, namely, control, chitosan-modified material, nanodiamond-modified material, and chitosan-nanodiamond-modified material. Twenty-four specimens were prepared for each material. The surface roughness was determined using a profilometer with a cut-off of 0.25 mm. The baseline color was measured according to the CIE L*a*b* system using a reflectance spectrophotometer. After these tests, the specimens were individually immersed in cola soft drink, red wine, or distilled water (n = 8) for 28 days. After the aging, the surface roughness and final color were re-evaluated. The color stability was determined using the difference between the coordinates obtained before and after the aging process. The data on roughness and color change were evaluated using ANOVA and the Tukey test (α = 0.05). The results show that the incorporation of nanodiamonds and chitosan into a bisacrylic resin provided a better color stability to the materials (p = 0.007). The storage in red wine resulted in a higher variation in the surface roughness values, especially when only the nanodiamond was incorporated to the material (p < 0.05). The incorporation of both chitosan and nanodiamonds are promising in providing an improvement in the properties of the bisacrylic resin when they are simultaneously incorporated in the product.

Conceptos fundamentales del protocolo modificado de plastinación a temperatura ambiente con silicona, con posterior pigmentación, y su aplicación para la conservación de placenta humana / Fundamental concepts of the modified room temperature plastination protocol with silicone, with subsequent pigmentation, and its application for the conservation of human placenta

RESUMEN: El auge experimentado en los últimos años en la aplicación de las técnicas anatómicas para la conservación de muestras anatómicas está directamente relacionado con la necesidad de preservación de los escasos especímenes con que cuentan las instituciones universitarias en relación a aumentar el tiempo de utilización del mismo. En este sentido, la plastinación es la técnica anatómica que más se destaca y que permite preservar por tiempo indeterminado, sin toxicidad, las preparaciones anatómicas. Presentamos el protocolo modificado de plastinación a temperatura ambiente con silicona, desarrollado en el Laboratorio de Plastinación y Técnicas Anatómicas de la Universidad de La Frontera, con el objetivo de aplicarla a la conservación de una placenta humana, la cual posteriormente fue pigmentada para otorgarle un aspecto más cercano a lo real.

SUMMARY: The surge experienced in recent years in the application of anatomical techniques for the conservation of anatomical samples is directly related to the need to preserve the few specimens that university institutions have in relation to increase the time of use of the same. In this sense, the plastination is the anatomical technique that stands out and that allows to preserve indefinitely, without toxicity, the anatomical preparations. We present the modified plastination protocol at room temperature with silicone, developed in the Laboratory of Plastination and Anatomical Techniques of the University of La Frontera, with the aim of applying it to the conservation of a human placenta, which was subsequently pigmented to give it an appearance closer to the real.

Antifungal efficiency of chemically and thermally-activated acrylic resins after surface treatment using poly (diallyldimethylammonium chloride)

Abstract INTRODUCTION: Acrylic resins are used in the preparation of facial prostheses and may be colonized by fungi. Here, we verified the antifungal efficacy of this material after surface treatment using poly (diallyldimethylammonium chloride). METHODS: Acrylic resin specimens with and without surface treatment were subjected to tests for fungistatic and fungicidal activities. Standard strains of Candida albicans and Aspergillus niger were used. RESULTS: After surface treatment, the fungistatic and fungicidal efficacies of the resins against C. albicans and fungistatic action against A. niger were verified. CONCLUSIONS: The surface treatment was a determinant of the antifungal activity of the material.

The effect of nanodiamonds on candida albicans adhesion and surface characteristics of PMMA denture base material - an in vitro study

Abstract Candida albicans is the main causative pathogen of denture stomatitis, which affects many complete denture patients. Objective: To evaluate the effect of different concentrations of nanodiamonds (NDs) added to polymethyl methacrylate (PMMA) denture base material on Candida albicans adhesion as well as on surface roughness and contact angle. Methodology: Acrylic resin specimens sized 10×10×3 mm3 were prepared and divided into four groups (n=30) according to ND concentration (0%, 0.5%, 1%, 1.5% by wt). Surface roughness was measured with a profilometer, and the contact angle with a goniometer. The effect of NDs on Candida albicans adhesion was evaluated using two methods: 1) slide count and 2) direct culture test. Analysis of variance (ANOVA) and Tukey's post hoc test were used in the statistical analyses. Results: Addition of NDs decreased the Candida albicans count significantly more than in the control group (p<0.05), with a lowest of 1% NDs. Addition of NDs also significantly decreased the surface roughness (p<0.05), but the contact angle remained the same. Incorporation of NDs into the PMMA denture base material effectively reduced Candida albicans adhesion and decreased surface roughness. Conclusion: PMMA/NDs composites could be valuable in the prevention of denture stomatitis, which is considered one of the most common clinical problems among removable denture wearers.

Effect of cavity preparation design and ceramic type on the stress distribution, strain and fracture resistance of CAD/CAM onlays in molars

Abstract Objective This study aimed to evaluate the effect of the cavity preparation and ceramic type on the stress distribution, tooth strain, fracture resistance and fracture mode of human molar teeth restored with onlays. Material and Methods Forty-eight molars were divided into four groups (n=12) with assorted combinations of two study factors: BL- conventional onlay preparation with boxes made from leucite ceramic (IPS-Empress CAD, Ivoclar Vivadent); NBL- conservative onlay preparation without boxes made from leucite ceramic; BD- conventional onlay preparation with boxes made from lithium disilicate glass ceramic (IPS e.max CAD, Ivoclar Vivadent); NBL- conservative onlay preparation with boxes made from lithium disilicate glass ceramic cuspal deformation (µS) was measured at 100 N and at maximum fracture load using strain gauge. Fracture resistance (N) was measured using a compression test, and the fracture mode was recorded. Finite element analysis was used to evaluate the stress distribution by modified von Mises stress criteria. The tooth strain and fracture resistance data were analyzed using the Tukey test and two-way ANOVA, and the fracture mode was analyzed by the chi-square test (α=0.05). Results The leucite ceramic resulted in higher tooth deformation at 100 N and lower tooth deformation at the maximum fracture load than the lithium disilicate ceramic (P<0.001). The lithium disilicate ceramic exhibited higher fracture resistance than the leucite ceramic (P<0.001). The conservative onlay resulted in higher fracture strength for lithium disilicate ceramic. Finite element analysis results showed the conventional cavity preparation resulted in higher stress concentration in the ceramic restoration and remaining tooth than the conservative onlay preparation. The conservative onlays exhibited increased fracture resistance, reduced stress concentration and more favorable fracture modes. Conclusion Molars restored with lithium disilicate CAD-CAM ceramic onlays exhibited higher fracture resistance than molars restored with leucite CAD-CAM ceramic onlays.

Porosity, water sorption and solubility of denture base acrylic resins polymerized conventionally or in microwave

Abstract The proper selection of polymerization cycle is important to prevent overheating of the monomer that could cause degradation, porosity and, consequently, deleterious effects on the denture base properties. Objective This study evaluated the porosity, water sorption and solubility of acrylic resins (Vipi Cril-VC and Vipi Wave-VW) after conventional or microwave polymerization cycles. Material and Methods Specimens (n = 10) were made and cured: 1-WB = 65°C during 90 min + boiling during 90 min (VC cycle - control group); 2-M25 = 10 min at 270 W + 5 min at 0 W + 10 min at 360 W (VW cycle); 3-M3 = 3 min at 550 W; and 4-M5 = 5 min at 650 W. Afterward, they were polished and dried in a dessicator until a constant mass was reached. Specimens were then immersed in distilled water at 37°C and weighed regularly until a constant mass was achieved. For porosity, an additional weight was made with the specimen immediately immersed in distilled water. For water sorption and solubility, the specimens were dried again until equilibrium was reached. Data were submitted to 2 way-ANOVA and Tukey HSD (α=0.05). Results Porosity mean values below 1.52% with no significant difference among groups for both materials were observed. Resins showed water sorption and solubility values without a significant difference. However, there was a significant difference among groups for these both properties (P<0.013). The highest sorption (2.43%) and solubility (0.13%) values were obtained for WB and M3, respectively. Conclusions The conventional acrylic resin could be polymerized in a microwave since both the materials showed similar performance in the evaluated properties. Shorter microwave cycles could be used for both the materials without any detectable increase in volume porosity.

Materiales para prótesis provisionales / Materials for provisional prosthetics

Las restauraciones provisionales utilizadas en prótesis fija han cambiado y evolucionado en los últimos años como consecuencia de los recientes avances en odontología restauradora y ha pasado a ser un factor de grandes demandas y exigencias estéticas. En la actualidad la posibilidad de elección de resinas para provisionales en el mercado son diversas. Cada material con sus ventajas y desventajas.El presenta artículo aborda los materiales que en la actualidad son usados con más frecuencia para la confección de prótesis provisionales en nuestro mercado y que posibilidades nos brinda.

The provisional restorations used in fixed prostheses have changed and evolved in recent years as a result of recent advances in restorative dentistry and has become a factor of great demands and aesthetic demands. At present the possibility of choosing resins for temporary in the market are diverse. Each material with its advantages and disadvantages.This article addresses the materials that are currently used most frequently for the preparation of temporary prostheses in our market and what possibilities they provide us.

Silver nanoparticle incorporation effect on mechanical and thermal properties of denture base acrylic resins

ABSTRACT Objective The aim of the present study was to evaluate the mechanical and thermal characteristics of two denture base acrylic resins containing silver nanoparticles (AgNPs). Material and Methods Two different acrylic denture base resins (heat-polymerized and microwave polymerized) containing 0.3, 0.8 and 1.6 wt% AgNPs were evaluated for flexural strength, elastic modulus and impact strength. The glass transition temperature (Tg) and relative heat capacity (Cp) of the samples were determined from the Differential Scanning Calorimetry (DSC) results. For statistical analysis, two-way ANOVA and Tukey-HSD tests were performed. Results Addition of 0.8% and 1.6% AgNPs in microwave-polymerized resin significantly decreased the transverse strength and elastic modulus. In terms of impact strength, the addition of AgNPs has no effect on both resin groups. Glass transition temperature (Tg) was decreased with the addition of AgNPs for both denture base resins. Conclusions The incorporation of AgNPs, generally used for antimicrobial efficiency, affected the transverse strength of the denture base acrylic resins depending on the concentration of nanoparticles. Tg was decreased with the addition of AgNPs for both denture base resins.

Dispositivo acrílico simples para medir as alterações nos tecidos moles da maxila após procedimentos implantares ou restauradores protético-periodontais / A simple acrylic device to measure maxillary soft tissue alterations after implant and/or restorative periodontal and prosthetic procedures

Alterações nos tecidos moles, na zona estética, podem ocorrer por procedimentos restauradores associados ou não à Implantodontia. Os autores propuseram um dispositivo acrílico simples associado a uma sonda periodontal, para verificação destes níveis em todos os momentos do tratamento reabilitador. O dispositivo em questão também pode ser desenhado e confeccionado em qualquer sistema CAD/CAM.

Soft tissue changes in the esthetic zone can occur after restorative procedures associated or not to implant dentistry. The authors describe a simple acrylic device associated to a periodontal probe to verify those levels during all treatment procedure steps. Also, this device can be design and milled at any CAD/CAM system.

Porosity of temporary denture soft liners containing antifungal agents

ABSTRACT Incorporation of antifungals in temporary denture soft liners has been recommended for denture stomatitis treatment; however, it may affect their properties. Objective: To evaluate the porosity of a tissue conditioner (Softone) and a temporary resilient liner (Trusoft) modified by minimum inhibitory concentrations (MICs) of antifungal agents for Candida albicans biofilm. Material and Methods: The porosity was measured by water absorption, based on exclusion of the plasticizer effect. Initially, it was determined by sorption isotherms that the adequate storage solution for specimens (65×10×3.3 mm) of both materials was 50% anhydrous calcium chloride (S50). Then, the porosity factor (PF) was calculated for the study groups (n=10) formed by specimens without (control) or with drug incorporation at MICs (nystatin: Ny-0.032 g, chlorhexidine diacetate: Chx-0.064 g, or ketoconazole: Ke-0.128 g each per gram of soft liner powder) after storage in distilled water or S50 for 24 h, seven and 14 d. Data were statistically analyzed by 4-way repeated measures ANOVA and Tukey's test (α=.05). Results: Ke resulted in no significant changes in PF for both liners in water over 14 days (p>0.05). Compared with the controls, Softone and Trusoft PFs were increased at 14-day water immersion only after addition of Ny and Chx, and Chx, respectively (p<0.05). Both materials showed no significant changes in PF in up to 14 days of S50 immersion, compared with the controls (p>0.05). In all experimental conditions, Softone and Trusoft PFs were significantly lower when immersed in S50 compared with distilled water (p<0.05). Conclusions: The addition of antifungals at MICs resulted in no harmful effects for the porosity of both temporary soft liners in different periods of water immersion, except for Chx and Ny in Softone and Chx in Trusoft at 14 days. No deleterious effect was observed for the porosity of both soft liners modified by the drugs at MICs over 14 days of S50 immersion.

Influence of resin cement shade on the color and translucency of ceramic veneers

ABSTRACT Objective This in vitro study evaluated the effect of two different shades of resin cement (RC- A1 and A3) layer on color change, translucency parameter (TP), and chroma of low (LT) and high (HT) translucent reinforced lithium disilicate ceramic laminates. Material and Methods One dual-cured RC (Variolink II, A1- and A3-shade, Ivoclar Vivadent) was applied to 1-mm thick ceramic discs to create thin RC films (100 µm thick) under the ceramics. The RC was exposed to light from a LED curing unit. Color change (ΔE) of ceramic discs was measured according to CIEL*a*b* system with a standard illuminant D65 in reflectance mode in a spectrophotometer, operating in the light range of 360-740 nm, equipped with an integrating sphere. The color difference between black (B) and white (W) background readings was used for TP analysis, while chroma was calculated by the formula C*ab=(a*2+b*2)½. ΔE of 3.3 was set as the threshold of clinically unacceptable. The results were evaluated by two-way ANOVA followed by Tukey's post hoc test. Results HT ceramics showed higher ΔE and higher TP than LT ceramics. A3-shade RC promoted higher ΔE than A1-shade cement, regardless of the ceramic translucency. No significant difference in TP was noted between ceramic discs with A1- and those with A3-shade cement. Ceramic with underlying RC showed lower TP than discs without RC. HT ceramics showed lower chroma than LT ceramics, regardless of the resin cement shade. The presence of A3-shade RC resulted in higher chroma than the presence of A1-shade RC. Conclusions Darker underlying RC layer promoted more pronounced changes in ceramic translucency, chroma, and shade of high translucent ceramic veneers. These differences may not be clinically differentiable.

Effect of Polymerization Cycles on Gloss, Roughness, Hardness and Impact Strength of Acrylic Resins

Abstract The aim of this study was to evaluate the conventional and boiled polymerization cycles on gloss, roughness, hardness and impact strength of acrylic resins. Samples were made for each Classico and QC-20 materials (n=10) in dental stone molds obtained from rectangular metallic matrices embedded in metallic flasks. The powder-liquid ratio and manipulation of the acrylic resins' were accomplished according to manufacturers' instructions and the resins were conventionally packed in metallic flasks. After polymerization by (1) conventional: 74 °C for 9 h (Classico) and (2) boiled: 20 min (QC-20) cycles, the samples were deflasked after cooling at room temperature and conventionally finished and polished. The properties were evaluated after storage in water at 37 °C for 24 h. Gloss was verified with Multi Gloss 268 meter (Konica Minolta), surface roughness was measured with Surfcorder SE 1700 rugosimeter (Kosaka), Knoop hardness number was obtained with HMV-200 microdurometer, and impact strength was measured in an Otto Wolpert-Werke device by Charpy system (40 kpcm). Data were subjected to Student's t-test (at α=0.05). The results were: Gloss: 67.7 and 62.2 for Classico and QC-20 resins, respectively; Surface roughness: 0.874 and 1.469 Ra-µm for Classico and QC-20, respectively; Knoop hardness: 27.4 and 26.9 for Classico and QC-20, respectively; and Impact strength: 37.6 and 33.6 kgf/cm2 for Classico and QC-20, respectively. No statistically significant difference (p>0.05)were found between the resins for the evaluated properties. In conclusion, conventional and boiled polymerization cycles had similar effects on gloss, roughness, hardness and impact strength of both Classico and QC-20 resins.

Resumo O propósito neste estudo foi avaliar os ciclos de polimerização convencional e por fervura sobre o brilho, rugosidade, dureza e resistência ao impacto de resinas acrílicas. Amostras foram confeccionadas para cada resina Clássico ou QC-20 (n=20) em moldes de gesso obtidos de matrizes metálicas retangulares incluídas em muflas metálicas. A proporção monômero/polímero das resinas e manipulação foram de acordo com as recomendações dos fabricantes e a massa convencionalmente incluída em muflas metálicas. Após polimerização nos ciclos (1) convencional: 74 °C por 9 horas (Clássico) e (2) fervura: 20 min (QC-20), as amostras foram demufladas após esfriadas em temperatura ambiente e convencionalmente acabadas e polidas. As propriedades foram avaliadas após armazenagem das amostras em água a 37 °C por 24 h. O brilho foi verificado com medidor Multi Gloss 268 (Konica Minolta), a rugosidade avaliada com rugosímetro Surfcorder SE 1700 (Kosaka), a dureza Knoop foi obtida com microdurômetro HMV-200 (Shimadzu) e a resistência ao impacto determinada pelo sistema Charpy (Otto Wolpert Werke). Os dados submetidos ao teste t de Student (α=0.05) mostraram que Os resultados foram: brilho: 67,7 e 62,2 para Clássico e QC-20, respectivamente; rugosidade: 0,874 e 1,469 Ra-µm para Clássico e QC-20, respectivamente; dureza: 27,4 e 26,9 para Clássico e QC-20, respectivamente; e resistência ao impacto: 37,6 e 33,6 kgf/cm2 para Clássico e QC-20, respectivamente. Não houve diference estatisticamente significante entre as resinas para as propriedades avaliadas. Conclui-se que os ciclos de polimerização convencional e por fervura promoveram similares efeitos sobre o brilho, rugosidade, dureza e resistência ao impacto para ambas as resinas Clássico e QC-20.

Efeito de cianoacrilatos e adesivo tissular a base de veneno de cobra na citotoxicidade sobre fibroblastos gengivais e estresse oxidativo sobre células do biofilme de C. albicans / Effect cyanoacrylate and snake venom tissue adhesive on cytotoxicity of gingival fibroblasts and oxidative stress of C. albicans biofilms

A estomatite protética é uma patologia que acomete muitos usuários de prótese total. Um dos principais fatores da sua etiologia é a fácil adesão de microrganismos, como a Candida albicans, à resina acrílica, principalmente devido às características de superfície facilitadoras deste material. Por esta razão, estuda-se materiais que possam modificar as características de superfície da resina acrílica sem alterar as suas propriedades mecânicas. A investigação das propriedades desses materiais, como a biocompatibilidade e como eles influenciam as células de C. albicans, é de extrema importância para uma futura aplicação clínica. Dessa forma, a proposta desta pesquisa foi avaliar a citotoxicidade sobre fibroblastos gengivais humanos (FGH) e o estresse oxidativo causado em células de C. albicans por 6 produtos (etil-cianoacrilato convencional -ECAc; etil-cianoacrilato em forma de gel formulação a -ECAga; etil-cianoacrilato em forma de gel formulação b -ECAgb; butil-cianoacrilato - BCA; octil-cianoacrilato OCA; selante tissular a base de veneno de cobra-VC;), que quando aplicados na superfície da resina acrílica, modificam suas características de superfície, visando diminuir a formação do biofilme de C. albicans. Espécimes de resina acrílica foram confeccionados e duas camadas de cada produto foram aplicadas nas superfícies. Cada espécime foi deixado em 1, 066 mL de meio de cultura durante 24 horas para extração e utilização do meio condicionado para os dois ensaios. Para a investigação da citotoxicidade, os FGH foram cultivados em placas de 96 poços, meios condicionado de cada grupo foram depositados em cada poço onde permaneceram em contato por 24, 48 e 72 h. Após o processamento para o ensaio de MTT as placas foram analisadas em espectrofotômetro a 500 nm. Foram realizados quatro experimentos independentes em triplicata (n=12). Para a investigação de estresse oxidativo (ERO) causado em C. albicans, biofilme foi desenvolvido em placas de 96 poços durante 24 h. Então, os meios condicionados foram adicionados aos poços e a placa foi mantida em agitadora durante 1 h. Após a retirada dos meios condicionados, foi adicionado a cada poço o reagente CellRox® Deep Red e leituras foram realizadas a cada 30 min durante 3 h em fluorímetro a 640/665nm. Amostras foram coletadas e ensaio de cultura microbiológica foi executado para a realização da normalização dos valores. Foram realizados 3 experimentos independentes em triplicata (n=9). Os resultados obtidos pelo ensaio MTT foram analisados por meio de ANOVA a 2 critérios, seguido pelo teste Tukey para a comparação entre grupos (p<0,05). Para o ensaio ROS, a análise estatística realizada foi ANOVA a 1 critério, seguida, igualmente, por Tukey (p<0,05). Os resultados mostraram que todos os grupos apresentaram certo grau de citotoxicidade quando comparados ao controle, com exceção do VC (ECAc

Denture stomatitis is a disease that affects many denture wearers. One of the main factors of its cause is the easy adhesion of microorganisms, such as Candida albicans, to acrylic resin, mainly due to its permissive surface characteristics. For this reason, materials that can modify surface characteristics of acrylic resin without changing its mechanical properties are being studied. The investigation of these materials features, such as biocompatibility and how they affect Candida albicans, is of utmost importance for future clinical application. Thus, the purpose of this study was to evaluate the cytotoxicity of human gingival fibroblasts (HGF) and oxidative stress in C. albicans cells after contact with 6 experimental products (conventional ethyl-cyanoacrylate -ECAc; ethyl-cyanoacrylate in gel formulation "a" -ECAga; ethyl-cyanoacrylate in gel formulation "b" -ECAgb; butyl- cyanoacrylate - BCA; octyl-cyanoacrylate -OCA; tissue adhesive based on snake venom -VC) applied to the surface of the resin acrylic, modifying its surface characteristics, in order to decrease C. albicans biofilm formation. Acrylic resin specimens were manufactured and two layers of each product were applied to the surfaces. Each specimen was immersed in 1,066 mL of growth media for 24 hours for extraction and the resulting conditioned media were used for both tests. To investigate cytotoxicity, HGF were cultured in 96-well plates and conditioned media from each group were deposited into each well, where they remained in contact for 24, 48 and 72h. After the MTT assay processing, plates were analyzed in a spectrophotometer at 500 nm. Four independent experiments were performed in triplicate (n=12). To investigate oxidative stress (ROS), C. albicans biofilm was developed in 96-well plates for 24 h, conditioned media were added to the wells and the plate was allowed to stir for 1 h. Then, conditioned media were removed and CellRox® Deep Red reagent was added to each well. Readings were performed every 30 min for 3 h in fluorometer at 640/665nm. Samples were collected and microbiological culture test was executed to values normalization. Three independent experiments were performed in triplicate (n=9). Results obtained in MTT assay were analyzed by two-way ANOVA and Tukey's test for comparison between groups (p<0.05). for comparison between groups (p<0.05). For ROS results, one-way ANOVA was performed followed by Tukey test, as well (p<0.05). The results showed that all groups presented different degrees of cytotoxicity when compared to control group, except for VC (ECAc

Influência da erosão dentária na adesão de braquetes ortodônticos colados ao esmalte com diferentes materiais / The influence of dental erosion on bond strength of orthodontic brackets bonded to enamel with different materials

O diagnóstico das lesões incipientes de erosão em esmalte é difícil de ser realizado e, em situações clínicas, poderá ocorrer a colagem de braquetes em superfícies erodidas. Este trabalho in vitro avaliou a adesão de braquetes ortodônticos ao esmalte dentário bovino hígido e previamente erodido, utilizando dois materiais para colagem. Os fatores em estudo foram condição prévia do esmalte em 2 níveis (com e sem erosão) e tipo de material de colagem em 2 níveis (Transbond XT e Fuji Ortho LC). A amostra foi composta por 160 coroas de incisivos bovinos, sendo metade dela submetida a desafio erosivo para formação de lesões artificiais de erosão e a outra metade permaneceu hígida. Na ciclagem erosiva as coroas foram imersas 8X/dia em Coca-cola® (10 min), seguido da imersão em saliva artificial (2 h), durante 5 dias. A outra metade da amostra ficou em saliva artificial por 5 dias. Braquetes de incisivo central superior foram colados às coroas hígidas (H) e erodidas (E), seguindo orientações dos fabricantes de cada material. As variáveis de resposta foram resistência ao cisalhamento e índice de remanescente adesivo (IRA). Os dados de resistência ao cisalhamento foram analisados por ANOVA 2 critérios e Teste de Tukey (p<0,05). Os resultados, expressos em megapascal, não mostraram diferenças na resistência ao cisalhamento entre esmalte erodido e hígido, tanto no grupo colado com resina (RH = 15,25 +3,72; RE = 15,79 +4,41) quanto colado com ionômero (IH = 10,70 +3,73; IE = 11,26 +3,70). A resina apresentou resistência à colagem superior ao ionômero. Na comparação do índice de remanescente adesivo, por meio do teste de Mann Whitney, o esmalte erodido apresentou valores mais altos para o IRA, evidenciando uma maior quantidade de material remanescente no esmalte, tanto no grupo colado com resina (p=0,044) quanto com ionômero (p<0,001). Conclui-se que a presença da lesão de erosão não interfere na resistência ao cisalhamento de braquetes colados ao esmalte tanto com resina quanto com cimento de ionômero de vidro. No entanto, independentemente do material de colagem, o índice de remanescente adesivo evidenciou uma maior adesão ao esmalte com erosão.(AU)

The diagnosis of initial erosion lesions on enamel is difficult and in some clinical situations, the professional bonds brackets to eroded surfaces without noting.This in vitro study evaluated the bond strength of orthodontic brackets bonded to eroded and sound bovine enamel with two different materials. The factors under study were enamel condition in two levels (with and without erosion) and type of bonding material in two levels (Transbond® XT and Fuji Ortho LC). The sample consisted of 160 bovine lower incisor teeth, half of the specimens was subjected to erosive challenge to form artificial erosive lesions and the other half remained sound. In the erosive cycling tooth crowns were immerged 8x/day in Coca-cola® (10 min), followed by immersion in artificial saliva for (2 h), for 5 days. The other half of the sample was maintained in artificial saliva for 5 days. At sequence, brackets were bonded to eroded (E) and sound (S) enamel, according to manufacturing recommendations of each material. The response variables were shear bond strength and adhesive remnant index (ARI). Shear bond strength data were analyzed by Two-way ANOVA and Tukeys test (p<0,05). The results, expressed in megapascal, did not show any difference between eroded and sound enamel, in both composite resin (RS = 15,25 +3,72; RE = 15,79 +4,41) and glass ionomer (IS = 10,70 +3,73; IE = 11,26 +3,70) groups. Composite resin showed higher shear bond strength compared to glass ionomer cement. In the comparison of adhesive remnant index using Mann Whitney test, eroded enamel presented higher scores for ARI, showing greater amount of material remaining on enamel, in both resin (p=0,04) and ionomer (p<0,001) groups. It was concluded that the presence of erosion lesions did not interfere on shear bond strength of brackets bonded to enamel with composite resin or glass ionomer cement. However, independently of the bonding material, adhesive remnant index showed higher bond strength to eroded enamel.(AU)